These lights are awesome! I have them in my garage. No more fumbling in the dark or not enough light. They switch on and off as programmed. - Christopher K. (Verified Buyer)
The LED Batten That Saves You Energy & Money
The enLighten Vico linear LED batten is packed with features to save you energy and money. These include:
- Easy to configure microwave motion sensor - reduces energy consumption by up to 90%.
- A dual wattage switch to optimise light levels and power usage.
- Two size options - choose between '2 Foot' and '4 Foot' sizes.
- Also available with emergency battery backup.
enLighten Vico Linear LED Batten - Key Features & Applications.
Configuring the Motion Sensor Is Easy
The included sensor allows the light fitting to dim down or switch off when no one is around. The microwave sensor sits behind the diffuser, so you can't even see it.
Here are the three modes of operation and main settings:
- On - When any movement is detected, the Vico switches to 100% brightness.
- Standby - After a set time with no movement (5 seconds, 30 seconds, 3 minutes, or 10 minutes), it goes into a standby mode of 20% brightness.
- Hold or Off - The fitting can stay in this standby mode indefinitely until motion is detected again. Or, it can switch off completely after a further 0 seconds, 90 seconds, or 3 minutes.
These settings are controlled by a series of 'dip switches' located behind the diffuser (front cover). You can select your preferred settings at the time of installation or change them again in the future if needed.
The Vico LED Batten is ideal for any area with intermittent usage. They're used in car parks, emergency exit stairwells, and other areas that need dependable 24/7 lighting.
NEW - 'Eco Dim' Dual Wattage Switch
The Vico now has an 'Eco Dim' switch which reduces power and light output by 50%. Therefore, a single Vico fitting can replace either twin-tube or single-tube fluoro light fittings.
| Model | Full Power Mode | Half-Power Mode |
| 1200mm | 7W (Standby) to 30W (On) | 3.5W (Standby) to 15W (On) |
| 600mm | 5W (Standby) to 16W (On) | 3W (Standby) to 8W (On) |
The power consumption of the emergency model (with battery charging) is up to 2W higher.
Specifications - enLighten Vico LED Linear Batten
| Fitting Type | Complete light fitting |
| Maximum Power Usage | 16W ('2 Foot') or 30W ('4 Foot') |
| Voltage | 220 - 240V AC |
| Lifetime | 100,000+ hour rated LEDs |
| Colour Temperature | 5000K (Cool White / Daylight) |
| Material | Polycarbonate |
| Light Output | 2,215 lumens (600mm) or 4,220 lumens (1200mm) |
| Sensor Type | Microwave |
| Sensor Override | Yes, see the installation instructions below for all settings |
| Ratings | IP65 (waterproof) and IK10 (highest level of impact resistance) |
| Dimensions | 665mm (length) x 110mm (width) x 86mm (depth), 1270mm (length) x 110mm (width) x 86mm (depth) |
| Weight | 1.8kg (600mm), 2.9kg (1200mm) |
| Battery Backup | No - see here |
| Installation | To be completed by an electrician.3 wire terminal blocks inside at the centre and end for electrical connection. Surface mounting brackets included. |
| Product Identifiers | BL06S, BL12S |
| Warranty | 5 Years |
| Further Details | Spec Sheet (PDF), Installation Instructions (PDF) |
Dimensions of the nominal 600mm (2 Foot) and 1200mm (4 Foot) Vico LED battens.
Frequently Asked Questions
How does the Vico's electricity usage compare to old fluoro tubes?
The table below shows how the power usage of the Vico is up to around 90% lower than old fashioned fluorescent tube battens. But don't forget, savings can be even higher if you set the light to turn off completely after a certain amount of time.
| Model | Old Twin Fluro's | Vico LED (On) | Vico LED (Standby) |
| 1200mm | 90W | 30W | 7W (92% less power) |
| 600mm | 45W | 16W | 5W (89% less power) |
Fluro tube usage is based on 2 x 18W T8 tube and 2 x 36W T8 tube fittings and includes losses in the ballast.
Do you sell an LED batten without a motion sensor?
Yes - if you do not require a motion sensor, see our complete range of LED batten lights.