Chamaeleon Deco Arctic White 21W LED Light with Sensor


Enlighten

$189.95 AUD 

Order now for next day dispatchFree delivery over $200Bulk discounts available

Quality White Oyster LED Light Fitting

The Chamaeleon Deco Arctic White from enLighten is ideal for use in lift lobbies, hallways, emergency stairwells, corridors, foyers and under the eaves outside. 

Its features include:

  • Integrated motion sensor and lux (light level) sensor for up to 90% energy savings.
  • Emergency battery back up model available (see drop down menu).
  • 5 year manufacturer's warranty.
  • IP65 (waterproof) and IK09 (high level of impact resistance).
  • See also Chamaeleon Deco Charcoal Black model.

 enLighten Chamaeleon Deco Light with Inbuilt Sensor

Chamaeleon Deco - an ideal lighting solution for low occupancy spaces.

Huge Energy Savings for 'Always On' Lighting

The Chamaeleon Deco delivers much higher energy savings than other similar looking light fittings. Whereas other lights remain on all day, the Deco has 3 modes: full brightness (21W), reduced brightness (9W), or off after no motion detected (0W). Apart from the motion sensor it also has an integrated daylight sensor so the light can remain off when natural light is available.

The Chamaeleon Deco Arctic White model is ideal for all areas in buildings where lights are otherwise left on continuously. The product has been used in residential strata buildings, hotels, hospitals, commercial offices, and many other applications.

Mounting, Microwave Sensor, & Timer Options

The Chamaeleon Deco can be wall or ceiling mounted and has a range of energy saving options.

 
Wall Mount
Ceiling Mount
Suggested installation height
1-1.8m
2.5-6m
Maximum suggested spacing Every 5m Every 6m
Detection range
Approx 6m
Approx 8m

 
Sensitivity Settings - The standard detection range (above) can be reduced to 75%, 50%, 25% or 10%. This is handy if you need to 'tune' the microwave occupancy sensor to not switch on too readily in certain environments.

Time Delay Settings - The time that the light remains on at full brightness after movement has ceased can be varied between 5s, 30s, 1m, 5m, 15m or 30 minutes. We recommend 1m for corridors and 5m for lobbies.

Daylight Sensor Adjustment - The integrated PE (photoelectric) cell can be used to make sure the light only turns on at certain ambient light levels. Options are 2 lux (dark), 5 lux, 10 lux (twilight), 30 lux, 50 lux, or photocell disabled (default setting). Note: this setting can only be used if the standby is set to 0% (see below).

Chamaeleon Deco DIP Switches

The above 3 settings can be easily adjusted with a series of 'DIP switches' on the light fitting. See page 2 of instruction manual below for precise details.

Standby Brightness Mode - The amount of light emitted can either be 20% or 0% when no movement detected. In most instances we recommend the 0% setting for maximum energy savings. See page 4 of installation guide (below) for details.

Specifications - Chamaeleon Deco Arctic White

Fitting Type Wall or ceiling mounted complete light fitting
Power Consumption 21W standard, 23W emergency
Voltage 220 - 240V
Lifetime 54,000 hours
Colour Temperature Neutral White 4000K
Material Die cast aluminium (body) and polcarbonate cover
Light Output 1,800 Lumens
Ratings IP65 (waterproof) and IK09 (high level of impact resistance)
Dimensions 340mm (diameter) by 112mm (depth)
Weight 1.48kg standard, 1.79kg emergency
Battery For emergency model: replaceable 7.2V Ni-Cd 1800mAh battery. Allows light to run for at least 90 minutes in a blackout.
Installation To be completed by an electrician
Product Identifiers D-CHAMC-AW, D-CHAMC-E-AW, enLighten Chamaeleon Deco Standard or Emergency with in-built sensor - arctic white.
Further Documentation
Spec Sheet (PDF), Installation Instructions (Standard & Emergency), IES file for professional lighting designers (link).

Frequently Asked Questions

What is the recommended light spacing in a corridor?

If you are replacing existing oyster light fittings you can usually just replace every light fitting (ie. one for one replacement). In some corridors, where the existing lights are quite close together, you can get away with replacing every second light fitting. In either case the maximum recommend spacing between light fittings is approximately 5 to 6 metres for normal ceiling heights.

Can I install the light where it will be exposed to direct sunlight?

It is not recommended, as the polycarbonate cover is not UV stabilised. We recommend the other Chamaeleon Deco model in these instances (which is UV stabilised).

How much will I save by installing this light fitting?

Energy and cost savings can be very substantial, but will depend on a wide range of factors. Taking the example of many apartment buildings with corridor lighting on 24/7 we have the following potential scenarios:

Light Fitting Average Load (Watts) Annual Operating Cost
Existing Oyster Light with T5 Circular Fluorescent Tube 32 $70
Existing Oyster Light with 2x18W PL CFL Bulbs 45 $99
NEW Chamaeleon Deco 21W LED (off in standby) 4 $9

The above example shows how you can often achieve energy savings up to 90% in some buildings. This gives a simple payback period of around 3 years once installation costs have been added.

Don't forget these light fittings also facilitate maintenance cost savings as well, which are not included above. More importantly, they usually produce a better and brighter quality of light than existing lights. In fact, we often find it is this final point of better lighting (not just the energy savings) which really wins over our customers.


Delivery Info Returns & Warranty Bulk Discounts Contact

Chamaeleon Deco Arctic White 21W LED Light with Sensor has a rating of 5.0 stars based on 1 reviews.

Got a Question?

stop sign

Please see our FAQ, delivery, and product pages for commonly asked questions and answers.

About us

Reduction Revolution Pty Ltd (ABN 74 141 672 764) is an Australian owned and operated business focused on energy efficiency and sustainability.

Australia New Zealand Map

Since 2010 we have supplied over 30,000 customers across Australia & New Zealand with quality products to slash their energy usage. Click the links below to find out more.


About Us
Blog Posts - Frequently Asked Questions - Delivery Details - Discounts & Wholesale - Warranty & Returns - Contact - Search

Education & Training
Energy Audits - Energy Freedom - Sustainability Course - Blog

Meters & Monitors
Power Meters - Energy Monitors - Thermal Imaging - Thermometers - Water Monitor - Light Meter

LED Lighting
Downlights - Light Bulbs - Filament Bulbs - LED Tubes - Oyster Lights - Strip Lights - Batten Lights - Panels / Troffers - High Bays - Motion Sensors - Floodlights - Emergency Lights

Energy Savers
Heating & Cooling - Hot Water - Cooking - Standby & Control - Pool Pumps - Portable Power

Latest Blog Posts

  • How to Install a Solar Energy Monitor

    The Efergy Engage Hub is a popular energy monitoring solution for households with solar power. Reason being - it tracks both household power consumption and solar power production. But before you jump in, you need to understand how it works. The physical... read more

  • How to Check if You Have a 3 Phase or Single Phase Power Supply (& Solar)

    Single phase or three phase, that is the question. Well, at least if you're browsing our range of wireless energy monitors. That's because most energy monitors use 'CT sensor clamps' to measure power consumption. And to capture all your usage... read more

  • Don't Waste Your Money on Battery Storage Until You Have One of These

    Everyone seems to be talking about the Tesla Powerwall and lithium batteries for energy storage. But I'd like to introduce a smarter and much cheaper way to store energy. Hot Water as Cheap & Efficient Energy Storage Much like storing... read more